KARRAY / PRODUCT DETAILS

4006 mini case and power supply

Survive in development, continuously optimize, and promote rapid development of enterprises with good reputation and scientific management

4006 mini case and power supply image

4006 mini case and power supply

Product model:

Brief description:Accommodates up to 6 NIM standard modules

  • Manufacturer strength

    Manufacturer Strength
  • Valid warranty

    Valid Warranty
  • Quality assurance

    Quality Assurance

Products

PRODUCT CATEGORY

Detailed introduction

ORTEC 4006 Minibin and Power Supply
  • Accommodates up to 6 NIM standard modules with a compact 24cm x 32cm desktop footprint
  • Regulated DC power supply: ±6 V @ 4 A, ±12 V @ 1.5 A, ±24 V @ 0.75 A and 120 V ac @ 0.5A
  • 120 W DC power at 23°C, 80 W at temperatures up to 50°C
  • Overvoltage protection prevents damage to +5 V and -5.2 V integrated circuits
  • Short circuit and overload protection with LED fault indicator
  • Available with 100, 120, 220 or 240 V AC at 50 or 60 Hz
  • Two standard preamplifier power sockets

If a small number of NIM modules must be located close to moving parts in a measurement system, the compact Model 4006 mini chassis and power supply is the ideal solution. Its compact 24cm x 32cm footprint maximizes desktop space. It can run at full power on solid surfaces because the cooling air intake and exhaust design comes from the rear, eliminating the need for free airflow from below. Model 4006 accommodates up to 6 standard single-width NIM modules, or proportionally reduced double-width modules.
  • information +

    • Download link 4006 Brochure
    • Download link 4006 Brochure (A4)
    • Download link 4006 Manual
  • More information +


    In addition to the standard ±24V and ±12V DC supplies, ±6V voltages are also available to meet the high current requirements of TTL and ECL logic widely used in new NIM modules. A full load of 0.75 A on two 24 V supplies, 1.5 A on two 12 V supplies, and 4 A on two 6 V supplies provides a total of 120W of DC power at room temperature (23°C). Can drive a total load of 80 W DC at ambient temperatures up to 50°C. A standard 60 VA with 120 V AC is also provided on the module power connector, which is independent of the actual AC voltage applied to the main power line. Two 9-pin D-type connectors on the rear panel conveniently provide ±6V, ±12V and ±24V power to the preamplifier using industry-standard preamplifier power plugs.

    The Type 4006 power supply integrates a wide range of protection features. The ±6 V power lines contain crowbar circuitry to protect TTL and ECL integrated circuits from overvoltage conditions. All six DC power lines contain protective foldback circuitry that automatically reduces output voltage in the event of excessive load current or a short circuit. When the supply voltage drops due to overload, the green LED indicator will turn red. If the voltage drops to zero due to a low impedance short circuit, the LED will go out. Thermal cut-off switch prevents power supply from overheating. When the radiator temperature is within the safe temperature range of 15°C, the red temperature warning indicator light will illuminate. If safe temperatures are exceeded, all power to the device automatically shuts down. Power automatically resumes when the temperature drops below safe limits. There is no high-temperature external heat sink to prevent accidental contact. All heat sinks are inside the device and are cooled by powerful fans. The AC power input is protected by a fuse and the device meets all CE requirements.

    A power input module with standard IEC connectors and optional 100, 120, 220 and 240 AC input voltages at 50 or 60 Hz makes the 4006 model compatible with nearly all country power cords and AC outlets.

  • Specifications +


    Power box

    machinery
    Tolerance

    conform toDOE/ER-0457Trequirements are available with allNIMStandard modules are interchangeable.

    module
    connector

    6. The connector complies withDOE/ER-0457Tregulations.

    module
    connector
    Wiring

    All module connectors comply withDOE/ER-0457TPin assignment requirements (+6 V、-6 V、+12 V、-12 V、+24 V、-24 V, power loops, high quality ground loops and120 V AC) parallel connection.

    Preamp power supply
    connector

    Two industry standard female headers9needleDType connector is mounted on the rear panel and wired via the following pin assignments. These connectors work withORTECpreamplifiers and most otherNIMMatches the standard preamp power connector on the manufacturer's preamplifier.

    Pin number

    DC voltage

    1
    2
    3
    4
    5
    6
    7
    8
    9

    ground
    ground
    +6 V
    +12 V
    -6 V
    -24 V
    +24 V
    No connection
    -12 V

    structure

    Painted aluminum housing with cadmium-plated steel perforated top/Bottom module mounting plate and connector mounting plate. Plastic front bezel and rail inserts. Rubber feet to protect the tabletop. All heatsinks are internal and cooled by a powerful fan. Cooling air enters from the lower rear, flows through the power supply and modules, and is finally discharged from the upper rear.




    power supply

    Input

    100, 120, 220, 240 V AC,50or60 Hz,400 VA, according toIEC801filteredEMI. Overvoltage categoryII, pollution level2. Voltage regulation allows+10% to-12% of nominal voltage range. for120 WDC load,120 V ACThe input current is usually3 A rms. The rear power input module is provided with a standardIECPlug for connecting a power cord compatible with local AC voltage outlets. The power input module selects the required input voltage and includes an input fuse. for100or120 V AC, the fuse rating is4 A,250 V(SLO-BLO), the size is3AG;for220or240 V AC, the fuse rating is2 A,250 V(T), the size is5 x 20 mm。

    DC output

    provided to6module power connector and2The current ratings for each voltage of the preamplifier power connectors are:

    DC voltage

    current

    DC voltage

    current

    +24 V
    +12 V
    +6 V

    0.75 A
    1.5 A
    4 A

    -24 V

    -12 V

    -6 V

    0.75 A
    1.5 A
    4 A


    Total DC output power:23°Ctime is120 W, in Gundam50°CAt the ambient temperature of80 W。

    120 Vcommunicate
    output

    Use120 VFor AC power, the power input fuse. When the DC load is80 W, the input voltage is100、220or240volts AC, limited to60 VA。

    DC regulation rate

    in1Measurements completed in minutes, over the combined range of zero to full load and the specified input voltage range, for ±12 Vand±24 V,<±0.1% (usually ±0.05%), while for ±6 V,<±0.2% (usually ±0.1%). passing by60After minutes of warm-up, at constant ambient temperature24hours, within the same load and input range, for ±12 Vand±24 V, adjustment rate<±0.3% for ±6 V, adjustment rate<±0.6%。

    output
    impedance

    In Gundam100 kHzat the frequency<0.3 Ω。

    long term
    Stability

    at constant load, line voltage and ambient temperature6Within a month, the DC output voltage changes<±0.5%(warm up60minutes).

    temperature
    coefficient

    The DC output voltage is at0to50°Cchanges in range<±0.02%/°C。

    Noise and ripple

    in50 MHzBandwidth oscilloscope observed peak-to-peak<3 mV。

    Voltage adjustment

    ±5%the minimum range. Adjustability<± of supply voltage0.05%。

    restore
    time

    For any voltage variation within the rated range or for load current from full load10% to100Change between % for restoration to rated voltage at all DC output terminals ±0.1% time required within range<100 μs。

    circuit protection

    The input power cord contains a fuse. If the temperature of the internal radiator exceeds110°C, the power will be automatically turned off by the internal switch. Recovery will occur automatically when the temperature drops to a safe value. If the radiator temperature exceeds95°C, a red light on the front panel will illuminate to warn of approaching temperature. All DC outputs contain a current foldback circuit to limit the output current to the rated value.120%. This feature provides short circuit and overload protection. Recovery will occur automatically after the overload is eliminated. ±6 VOvervoltage protection at the outputs prevents these outputs from exceeding ±7.5 V, to protect integrated circuits typically powered by these supply voltages.

    cooling

    Cooling air from the rear panel fan falls on the internal power supply heat sink and flows upward through all installedNIMmodule, and finally discharged from the upper rear. Therefore, no high-temperature external heat sink is exposed to prevent accidental contact.

    environment

    temperature0to50°C. For indoor use. relative humidity95%, no condensation. altitude2000m. Installation categoryII. pollution level2. match allCErequest.

























































    Controls and lights

    power supply

    The two-position rocker switch on the front panel is used to turn on or off the AC power supply on both sides.

    AC

    The green indicator light on the front panel lights up to indicate that AC power is connected. If the internal radiator temperature exceeds110°C, the power indicator light and output power will be turned off.

    temperature

    If the internal radiator temperature exceeds95°C, the front panel red light will illuminate to warn that the shutdown temperature limit is approaching. If the power is turned off because the heat sink temperature limit is exceeded, the temperature indicator light will also turn off.

    Status

    Six front panel indicators are used to indicate that the DC voltage is not within the regulation range due to current overload or short circuit. Green indicates normal operation (±5% range), red indicates an offset fault, and an off light means zero voltage due to a short circuit or lack of AC input power. The indicator light is marked with the supply voltage (-6 V,+ 6 V,-12 V,+12 V,-24 Vand+24 V) and the rated load current for each supply voltage.

    Calibration

    Six internal potentiometers mounted on the printed circuit board allow precise adjustment of the six DC output voltages.
















    machinery

    weight

    Net weight 12Kilogram (26pounds)Shipping weight 14Kilogram (31pounds)

    Size

    24.0cm width ×32.0cm depth ×35.2cm high (9.4inches wide ×12.6inches deep ×13.9inches high)






  • Ordering information +


    Model

    Description

    4006

    Mini case and power supply

Product consultation

Message box

Please enter the calculation result, such as: three plus four = 7

After submission, we will receive your requirements. You can also download the requirement file or call 021-20989890 directly.